Connect with us

TOP SCEINCE

Wireless receiver blocks interference for better mobile device performance

Published

on

Wireless receiver blocks interference for better mobile device performance


The growing prevalence of high-speed wireless communication devices, from 5G mobile phones to sensors for autonomous vehicles, is leading to increasingly crowded airwaves. This makes the ability to block interfering signals that can hamper device performance an even more important — and more challenging — problem.

With these and other emerging applications in mind, MIT researchers demonstrated a new millimeter-wave multiple-input-multiple-output (MIMO) wireless receiver architecture that can handle stronger spatial interference than previous designs. MIMO systems have multiple antennas, enabling them to transmit and receive signals from different directions. Their wireless receiver senses and blocks spatial interference at the earliest opportunity, before unwanted signals have been amplified, which improves performance.

Key to this MIMO receiver architecture is a special circuit that can target and cancel out unwanted signals, known as a nonreciprocal phase shifter. By making a novel phase shifter structure that is reconfigurable, low-power, and compact, the researchers show how it can be used to cancel out interference earlier in the receiver chain.

Their receiver can block up to four times more interference than some similar devices. In addition, the interference-blocking components can be switched on and off as needed to conserve energy.

In a mobile phone, such a receiver could help mitigate signal quality issues that can lead to slow and choppy Zoom calling or video streaming.

“There is already a lot of utilization happening in the frequency ranges we are trying to use for new 5G and 6G systems. So, anything new we are trying to add should already have these interference-mitigation systems installed. Here, we’ve shown that using a nonreciprocal phase shifter in this new architecture gives us better performance. This is quite significant, especially since we are using the same integrated platform as everyone else,” says Negar Reiskarimian, the X-Window Consortium Career Development Assistant Professor in the Department of Electrical Engineering and Computer Science (EECS), a member of the Microsystems Technology Laboratories and Research Laboratory of Electronics (RLE), and the senior author of a paper on this receiver.

Reiskarimian wrote the paper with EECS graduate students Shahabeddin Mohin, who is the lead author, Soroush Araei, and Mohammad Barzgari, an RLE postdoc. The work was recently presented at the IEEE Radio Frequency Circuits Symposium and received the Best Student Paper Award.

Blocking interference

Digital MIMO systems have an analog and a digital portion. The analog portion uses antennas to receive signals, which are amplified, down-converted, and passed through an analog-to-digital converter before being processed in the digital domain of the device. In this case, digital beamforming is required to retrieve the desired signal.

But if a strong, interfering signal coming from a different direction hits the receiver at the same time as a desired signal, it can saturate the amplifier so the desired signal is drowned out. Digital MIMOs can filter out unwanted signals, but this filtering occurs later in the receiver chain. If the interference is amplified along with the desired signal, it is more difficult to filter out later.

“The output of the initial low-noise amplifier is the first place you can do this filtering with minimal penalty, so that is exactly what we are doing with our approach,” Reiskarimian says.

The researchers built and installed four nonreciprocal phase shifters immediately at the output of the first amplifier in each receiver chain, all connected to the same node. These phase shifters can pass signal in both directions and sense the angle of an incoming interfering signal. The devices can adjust their phase until they cancel out the interference.

The phase of these devices can be precisely tuned, so they can sense and cancel an unwanted signal before it passes to the rest of the receiver, blocking interference before it affects any other parts of the receiver. In addition, the phase shifters can follow signals to continue blocking interference if it changes location.

“If you start getting disconnected or your signal quality goes down, you can turn this on and mitigate that interference on the fly. Because ours is a parallel approach, you can turn it on and off with minimal effect on the performance of the receiver itself,” Reiskarimian adds.

A compact device

In addition to making their novel phase shifter architecture tunable, the researchers designed them to use less space on the chip and consume less power than typical nonreciprocal phase shifters.

Once the researchers had done the analysis to show their idea would work, their biggest challenge was translating the theory into a circuit that achieved their performance goals. At the same time, the receiver had to meet strict size restrictions and a tight power budget, or it wouldn’t be useful in real-world devices.

In the end, the team demonstrated a compact MIMO architecture on a 3.2-square-millimeter chip that could block signals which were up to four times stronger than what other devices could handle. Simpler than typical designs, their phase shifter architecture is also more energy efficient.

Moving forward, the researchers want to scale up their device to larger systems, as well as enable it to perform in the new frequency ranges utilized by 6G wireless devices. These frequency ranges are prone to powerful interference from satellites. In addition, they would like to adapt nonreciprocal phase shifters to other applications.

This research was supported, in part, by the MIT Center for Integrated Circuits and Systems.



Source link

Continue Reading
Click to comment

Leave a Reply

TOP SCEINCE

Scientists discover new T cells and genes related to immune disorders

Published

on

By

Scientists discover new T cells and genes related to immune disorders


Researchers led by Yasuhiro Murakawa at the RIKEN Center for Integrative Medical Sciences (IMS) and Kyoto University in Japan and IFOM ETS in Italy have discovered several rare types of helper T cells that are associated with immune disorders such as multiple sclerosis, rheumatoid arthritis, and even asthma. Published July 4 in Science, the discoveries were made possible by a newly developed technology they call ReapTEC, which identified genetic enhancers in rare T cell subtypes that are linked to specific immune disorders. The new T cell atlas is publicly available and should help in the development of new drug therapies for immune-mediated diseases.

Helper T cells are kind of white blood cell that make up a large part of the immune system. They recognize pathogens and regulate the immune response. Many immune-mediated disease are caused by abnormal T cell function. In autoimmune diseases like multiple sclerosis, they mistakenly attack parts of the body as if they were pathogens. In the case of allergies, T cells overreact to harmless substances in the environment like pollen. We know of several common T cells, but recent studies have shown that rare and specialized types of T cells exist, and they might be related to immune-mediated diseases.

Within all cells, including T cells, there are regions of DNA called “enhancers”. This DNA does not code for proteins. Instead, it codes for small pieces of RNA, and enhances the expression of other genes. Variations in T cell enhancer DNA therefore lead to differences in gene expression, and this can affect how T cells function. Some enhancers are bidirectional, which means that both strands of the DNA are used as templates for enhancer RNA. The researchers from several different laboratories at RIKEN IMS, as well as colleagues at other institutes, teamed up to develop the new ReapTEC technology and look for connections between bidirectional T cell enhancers and immune diseases.

After analyzing about a million human T cells, they found several groups of rare T cell types, accounting for less than 5% of the total. Applying ReapTEC to these cells identified almost 63,000 active bidirectional enhancers. To figure out if any of these enhancers are related to immune diseases, they turned to genome-wide association studies (GWAS), which have reported numerous genetic variants, called single-nucleotide polymorphisms, that are related to various immune diseases.

When the researchers combined the GWAS data with the results of their ReapTEC analysis, they found that genetic variants for immune-mediated diseases were often located within the bidirectional enhancer DNA of the rare T cells that they had identified. In contrast, genetic variants for neurological diseases did not show a similar pattern, meaning that the bidirectional enhancers in these rare T cells are related specifically to immune-mediated diseases.

Going even deeper into the data, the researchers were able to show that individual enhancers in certain rare T cells are related to specific immune diseases. Overall, among the 63,000 bidirectional enhancers, they were able to identify 606 that included single-nucleotide polymorphisms related to 18 immune-mediated diseases. Lastly, the researchers were able to identify some of the genes that are the targets of these disease-related enhancers. For example, when they activated an enhancer that contained a genetic variant related to inflammatory bowel disease, the resulting enhancer RNA triggered upregulation of the IL7R gene.

“In the short-term, we have developed a new genomics method that can be used by researchers around the world,” says Murakawa. “Using this method, we discovered new types of helper T cells as well as genes related to immune disorders. We hope that this knowledge will lead to a better understanding of the genetic mechanisms underlying human immune-mediated diseases.”

In the long-term, the researchers believe follow-up experiments will be able to identify new molecules that can be used to treat immune-mediated diseases.



Source link

Continue Reading

TOP SCEINCE

The dawn of the Antarctic ice sheets

Published

on

By

The dawn of the Antarctic ice sheets


In recent years global warming has left its mark on the Antarctic ice sheets. The “eternal” ice in Antarctica is melting faster than previously assumed, particularly in West Antarctica more than East Antarctica. The root for this could lie in its formation, as an international research team led by the Alfred Wegener Institute has now discovered: sediment samples from drill cores combined with complex climate and ice-sheet modelling show that permanent glaciation of Antarctica began around 34 million years ago — but did not encompass the entire continent as previously assumed, but rather was confined to the eastern region of the continent (East Antarctica). It was not until at least 7 million years later that ice was able to advance towards West Antarctic coasts. The results of the new study show how substantially differently East and West Antarctica react to external forcing, as the researchers describe in the journal Science.

Around 34 million years ago, our planet underwent one of the most fundamental climate shifts that still influences global climate conditions today: the transition from a greenhouse world, with no or very little accumulation of continental ice, to an icehouse world, with large permanently glaciated areas. During this time, the Antarctic ice sheet built up. How, when and, above all, where, was not yet known due to a lack of reliable data and samples from key regions, especially from West Antarctica, that document the changes in the past. Researchers from the Alfred Wegener Institute, Helmholtz Centre for Polar and Marine Research (AWI) have now been able to close this knowledge gap, together with colleagues from the British Antarctic Survey, Heidelberg University, Northumbria University (UK), and the MARUM — Center for Marine Environmental Sciences at the University of Bremen, in addition to collaborators from the Universities in Aachen, Leipzig, Hamburg, Bremen, and Kiel, as well as the University of Tasmania (Australia), Imperial College London (UK), Université de Fribourg (Switzerland), Universidad de Granada (Spain), Leicester University (UK), Texas A&M University (USA), Senckenberg am Meer, and the Federal Institute for Geosciences and Natural Resources in Hanover, Germany.

Based on a drill core that the researchers retrieved using the MARUM-MeBo70 seafloor drill rig in a location offshore the Pine Island and Thwaites glaciers on the Amundsen Sea coast of West Antarctica, they were able to establish the history of the dawn of the icy Antarctic continent for the first time. Surprisingly, no signs of the presence of ice can be found in this region during the first major phase of Antarctic glaciation. “This means that a large-scale, permanent first glaciation must have begun somewhere in East Antarctica,” says Dr Johann Klages, geologist at the AWI who led the research team. This is because West Antarctica remained ice-free during this first glacial maximum. At this time, it was still largely covered by dense broadleaf forests and a cool-temperate climate that prevented ice from forming in West Antarctica.

East and West Antarctica react very different to external conditions

In order to better understand where the first permanent ice formed in Antarctica, the AWI paleoclimate modelers combined the newly available data together with existing data on air and water temperatures and the occurrence of ice. “The simulation has supported the results of the geologists’ unique core,” says Prof Dr Gerrit Lohmann, paleoclimate modeler at the AWI. “This completely changes what we know about the first Antarctic glaciation.” According to the study, the basic climatic conditions for the formation of permanent ice only prevailed in the coastal regions of the East Antarctic Northern Victoria Land. Here, moist air masses reached the strongly rising Transantarctic Mountains — ideal conditions for permanent snow and subsequent formation of ice caps. From there, the ice sheet spread rapidly into the East Antarctic hinterland. However, it took some time before it reached West Antarctica: “It wasn’t until about seven million years later that conditions allowed for advance of an ice sheet to the West Antarctic coast,” explains Hanna Knahl, a paleoclimate modeler at the AWI. “Our results clearly show how cold it had to get before the ice could advance to cover West Antarctica that, at that time, was already below sea level in many parts.” What the investigations also impressively show is how different the two regions of the Antarctic ice sheet react to external influences and fundamental climatic changes. “Even a slight warming is enough to cause the ice in West Antarctica to melt again — and that’s exactly where we are right now,” adds Johann Klages.

The findings of the international research team are critical for understanding the extreme climate transition from the greenhouse climate to our current icehouse climate. Importantly, the study also provides new insight that allows climate models to simulate more accurately how permanently glaciated areas affect global climate dynamics, that is the interactions between ice, ocean and atmosphere. This is of crucial importance, as Johann Klages says: “Especially in light of the fact that we could be facing such a fundamental climate change again in the near future.”

Using new technology to gain unique insights

The researchers were able to close this knowledge gap with the help of a unique drill core that they retrieved during the expedition PS104 on the research vessel Polarstern in West Antarctica in 2017. The MARUM-MeBo70 drill rig developed at MARUM in Bremen was used for the first time in Antarctica. The seabed off the West Antarctic Pine Island and Thwaites glaciers is so hard that it was previously impossible to reach deep sediments using conventional drilling methods. The MARUM-MeBo70 has a rotating cutterhead, which made it possible to drill about 10 meters into the seabed and retrieve the samples.

The research project, and the Polarstern expedition PS104 in particular, was funded by the AWI, MARUM, the British Antarctic Survey, and the NERC UK-IODP Programme.



Source link

Continue Reading

TOP SCEINCE

Moon ‘swirls’ could be magnetized by unseen magmas

Published

on

By

Moon ‘swirls’ could be magnetized by unseen magmas


Lunar swirls are light-colored, sinuous features on the Moon’s surface, bright enough to be visible from a backyard telescope. Some people think they look like the brushstrokes in an abstract painting. But these are not mere artistic flourishes: NASA images show that the tendrils from some lunar swirls extend for hundreds of miles.

Lunar swirls have defied easy explanation, but recent modeling and spacecraft data shed light on the twisty mystery. The data shows that rocks in the swirls are magnetized, and these rocks deflect or redirect solar wind particles that constantly bombard the Moon. Nearby rocks take the hit instead. Over time, neighboring rocks become darkened by chemical reactions caused by the collisions, while the swirls remain light colored.

But how did the rocks in lunar swirls get magnetized? The Moon does not have a magnetic field today. No astronaut or rover has yet visited a lunar swirl to investigate.

“Impacts could cause these types of magnetic anomalies,” said Michael J. Krawczynski, an associate professor of earth, environmental and planetary sciences in Arts & Sciences at Washington University in St. Louis. He notes that meteorites regularly deliver iron-rich material to areas on the Moon’s surface. “But there are some swirls where we’re just not sure how an impact could create that shape and that size of thing.”

Krawczynski believes it’s more likely that something else has locally magnetized the swirls.

“Another theory is that you have lavas underground, cooling slowly in a magnetic field and creating the magnetic anomaly,” said Krawczynski, who designed experiments to test this explanation. His results are published in the Journal of Geophysical Research: Planets.

Krawczynski and study first author Yuanyuan Liang, who recently earned her PhD in earth, environmental and planetary sciences in Arts & Sciences, measured the effects of different combinations of atmospheric chemistry and magmatic cooling rates on a mineral called ilmenite to see if they could produce a magnetizing effect.

“Earth rocks are very easily magnetized because they often have tiny bits of magnetite in them, which is a magnetic mineral,” Krawczynski said. “A lot of the terrestrial studies that have focused on things with magnetite are not applicable to the Moon, where you don’t have this hyper-magnetic mineral.”

But ilmenite, which is abundant on the Moon, can also react and form particles of iron metal, which can be magnetized under the right conditions, Krawczynski and his team found.

“The smaller grains that we were working with seemed to create stronger magnetic fields because the surface area to volume ratio is larger for the smaller grains compared to the larger grains,” Liang said. “With more exposed surface area, it is easier for the smaller grains to undergo the reduction reaction.”

“Our analog experiments showed that at lunar conditions, we could create the magnetizable material that we needed. So, it’s plausible that these swirls are caused by subsurface magma,” said Krawczynski, who is a faculty fellow in the university’s McDonnell Center for the Space Sciences.

Determining the origin of lunar swirls is considered key in understanding what processes have shaped the lunar surface, the history of a magnetic field on the Moon and even how the surfaces of planets and moons generally affect the space environment surrounding them.

This study will help interpret data acquired by future missions to the Moon, especially those that explore magnetic anomalies on the lunar surface. NASA intends to send a rover to the lunar swirl area known as Reiner Gamma in 2025 as part of the Lunar Vertex mission.

“If you’re going to make magnetic anomalies by the methods that we describe, then the underground magma needs to have high titanium,” Krawczynski said. “We have seen hints of this reaction creating iron metal in lunar meteorites and in lunar samples from Apollo. But all of those samples are surface lava flows, and our study shows cooling underground should significantly enhance these metal-forming reactions.”

For now, his experimental approach is the best way to test predictions about how unseen lava may be driving the magnetic effects of the mysterious lunar swirls.

“If we could just drill down, we could see if this reaction was happening,” Krawczynski said. “That would be great, but it’s not possible yet. Right now, we’re stuck with the surface.”



Source link

Continue Reading

Trending

Copyright © 2017 Zox News Theme. Theme by MVP Themes, powered by WordPress.