Solar Energy

Bulky additives could make cheaper solar cells last longer

Published

7 months ago

January 12, 2024

sarosh

Bulky additives could make cheaper solar cells last longer

by Staff Writers for Michigan News

Ann Arbor MI (SPX) Jan 12, 2024

Perovskites may also be combined with the silicon-based semiconductors that are prevalent in today’s solar panels to create “tandem” solar cells that could surpass the maximum theoretical efficiency of silicon solar cells.

“Silicon solar cells are great because they are very efficient and can last for a very long time, but the high efficiency comes with a high cost,” said Xiwen Gong, U-M assistant professor of chemical engineering. “To make high-purity silicon, temperatures over 1,000 degrees Celsius are needed. Otherwise, the efficiency won’t be as good.”

The high temperature comes with higher economic and environmental costs. But while perovskites can be produced at lower temperatures, they degrade when exposed to heat, moisture and air. As a result, the lifespan of perovskite today is too short to be commercially competitive in solar panels.

Gong’s research aims to make hardier perovskite solar cells, and her latest study published in the journal Matter suggests that bulky “defect pacifying” molecules are best at increasing the perovskites’ stability and overall lifespan.

Perovskite crystals contain lead atoms that aren’t fully bound to the other components within the perovskite. Such “undercoordinated sites” are defects often found on the crystal surfaces and at grain boundaries where there’s a break in the crystal lattice. These defects hinder the movement of electrons and speed up the decay of the perovskite material.

Engineers already know that mixing defect pacifying molecules into the perovskites can help lock up the undercoordinated lead, in turn preventing other imperfections from forming at high temperatures. But until now, engineers didn’t know exactly how a given molecule affected the hardiness of perovskite cells.

“We wanted to figure out what features on the molecules specifically improve the perovskite’s stability,” said Hongki Kim, a former postdoctoral researcher in chemical engineering and one of the study’s first authors.

To investigate the problem, Gong’s team created three additives with a range of shapes and sizes and added them into thin films of perovskite crystals, which can absorb light and convert it to electricity. Each additive contained the same or similar chemical building blocks, which made size, weight and arrangement the main properties differentiating them.

Then, the team measured how strongly the different additives interacted with perovskites and consequently influenced the formation of defects in the films. Larger molecules by mass were better at sticking to the perovskite because they had more binding sites that interact with perovskite crystals. As a result, they tended to be better at preventing defects from forming.

But the best additives also needed to take up a lot of space. Large but skinny molecules resulted in smaller perovskite grains during the manufacturing process. Smaller grains aren’t ideal because they also create perovskite cells with more grain boundaries, or more areas for defects to form. In contrast, bulky molecules forced larger perovskite grains to form, which in turn reduced the density of grain boundaries in the film.

Heating the perovskite films to over 200 degrees Celsius confirmed that bulky additives helped the films retain more of their characteristic slate black color and develop fewer structural defects.

“Both the size and configuration are important when designing additives, and we believe this design philosophy could be implemented across various perovskite formulations to further improve the lifetime of perovskite solar cells, light emitting devices and photodetectors,” said Carlos Alejandro Figueroa Morales, a doctoral student in macromolecular science and engineering and one of the study’s first authors.

Xiwen Gong is also an assistant professor of electrical and computer engineering, materials science and engineering, macromolecular science and engineering, and applied physics. The research was funded by the University of Michigan and relied on a scanning electron microscope funded by the National Science Foundation. Co-author Nancy Muyanja led the microscopy measurements at the Michigan Center for Materials Characterization.

Research Report:Molecular Design of Defect Passivators for Thermally Stable Metal Halide Perovskite Films

Source link

Solar Energy

3D-printed microstructure forest enhances solar steam desalination

Published

3 days ago

July 24, 2024

sarosh

3D-printed microstructure forest enhances solar steam desalination

by Clarence Oxford

Los Angeles CA (SPX) Jul 24, 2024

To address the global freshwater scarcity issue, researchers in Singapore have developed advanced solar steam generators (SSGs) for seawater desalination. This method, powered by renewable energy, mimics the natural water cycle by using solar energy to evaporate and purify water, offering a potentially cost-effective solution compared to traditional, energy-intensive desalination techniques. However, current SSG technologies face limitations due to the complexity of fabricating designs that maximize surface area for optimal water evaporation.

Drawing inspiration from nature, the team utilized 3D printing to create innovative SSGs. Their findings, published in Applied Physics Reviews, highlight a novel technique for manufacturing efficient SSGs and introduce a groundbreaking method for printing functional nanocomposites using multi-jet fusion (MJF).

“We created SSGs with exceptional photothermal performance and self-cleaning properties,” said Kun Zhou, a professor of mechanical engineering at Nanyang Technological University. “Using a treelike porous structure significantly enhances water evaporation rates and ensures continuous operation by preventing salt accumulation – its performance remains relatively stable even after prolonged testing.”

The technology works by converting light to thermal energy, where SSGs absorb solar energy and convert it to heat to evaporate water. The porous structure of the SSGs aids in self-cleaning by removing accumulated salt, ensuring sustained desalination performance.

“By using an effective photothermal fusing agent, MJF printing technology can rapidly create parts with intricate designs,” Zhou added. “To improve the photothermal conversion efficiency of fusing agents and printed parts, we developed a novel type of fusing agent derived from metal-organic frameworks.”

The SSGs feature miniature tree-shaped microstructures that mimic plant transpiration, forming an efficient, heat-distributing forest.

“Our bioinspired design increases the surface area of the SSG,” Zhou explained. “Using a treelike design increases the surface area of the SSG, which enhances the water transport and boosts evaporation efficiency.”

In both simulated environments and field trials, the SSGs exhibited a high rate of water evaporation. The desalinated water consistently met drinking water standards, even after extended testing.

“This demonstrates the practicality and efficiency of our approach,” Zhou said. “And it can be quickly and easily mass-produced via MJF commercial printers.”

The team’s work shows significant potential for tackling freshwater scarcity.

“Our SSGs can be used in regions with limited access to freshwater to provide a sustainable and efficient desalination solution,” said Zhou. “Beyond desalination, it can be adapted for other applications that require efficient solar energy conversion and water purification.”

Research Report:3D printing of bio-inspired porous polymeric solar steam generators for efficient and sustainable desalination

Source link

Solar Energy

Renewables overproduction turns electricity prices negative

Published

3 days ago

July 24, 2024

sarosh

Renewables overproduction turns electricity prices negative

By Nathalie Alonso and Catherine Hours

Paris (AFP) July 24, 2024

With the proliferation of solar panels and wind turbines an unusual phenomenon is becoming more and more frequent: wholesale electricity prices turn negative.

While that may brighten the mood of consumers whose power bills have surged in recent years, it could undermine the further development of renewables, a key element in the fight against global warming.

The increasingly frequent phenomenon is “extremely problematic” for the wind and solar sector, said Mattias Vandenbulcke, strategy director of the renewables industry group France Renouvelables.

“It allows some to have harmful, even dangerous rhetoric which says ‘renewables are useless’,” Vandenbulcke said.

In southern Australia, wholesale electricity prices have been negative some 20 percent of the time since last year, according to the International Energy Agency.

The share of negatively priced hours in southern California was above 20 percent in the first half of the year, more than triple from the same period in 2023, the IEA said.

In the first six months of the year in France, there were negative prices around five percent of the time, beating the record set last year, according to the electricity grid operator RTE.

In Switzerland the price tumbled as far as -400 euros (-$436) per megawatt hour on July 14. The lowest prices are usually recorded around midday during the summer when solar production is at its peak.

– ‘A warning signal’ –

The trend has been accelerating for the past three years as demand in Europe has unexpectedly dropped since the Covid pandemic and the war in Ukraine.

Prices turn negative on the spot wholesale electricity market when production is strong while demand is weak.

Around a fifth of the total is traded on this market, where electricity is bought for the following day.

Negative prices help reduce the bills of consumers, said Rebecca Aron, head of electricity markets at French renewables firm Valorem, but the impact is delayed and difficult to discern among the other factors that send prices higher and lower.

Large, industrial consumers that can shift production to times when prices are negative and buy on wholesale markets can reap the biggest rewards.

Negative prices are “a warning signal that there is way too much production on the electrical grid”, said energy analyst Nicolas Goldberg at Colombus Consulting.

Electricity grids need to be kept constantly in balance. Too much can lead to the electricity to increase in frequency beyond norms for some equipment. Too little can lead to some or all customers losing power.

There are currently few options to stock surplus electricity production so producers have to reduce output.

Many renewable producers stop their output when prices are set to turn negative. It takes one minute to stop output at a solar park, two to three minutes for a wind turbine.

But not all stop their production.

– Tripling renewables –

“Renewable energy can be controlled, but depending on production contracts, there might not necessarily be an incentive to stop,” said Mathieu Pierzo at French grid operator RTE, which has the responsibility for balancing the electricity load.

Some producers are paid a fixed price under their contract or are compensated by the state if prices fall below a certain level.

Fossil fuel and nuclear power plants can adjust their production to some extent, but halting and restarting output is costly.

In the future, solar and wind will also have to “participate more in balancing the electricity system”, Pierzo said.

Solar and wind production is set to rise further as nations agreed at the COP28 climate conference last year to triple renewable energy capacity by 2030 as part of efforts to limit warming to 1.5 degrees Celsius compared with pre-industrial levels.

“Rising frequency of negative prices sends an urgent signal that greater flexibility of supply and demand is needed,” the Paris-based IEA warned last week.

“The appropriate regulatory frameworks and market designs will be important to allow for an uptake in flexibility solutions such as demand response and storage,” it said.

nal-cho/abb/rl-lth/

FOSSIL GROUP

Source link

Solar Energy

NREL explores long-term strategies for sustainable perovskite solar panels

Published

3 days ago

July 24, 2024

sarosh

NREL explores long-term strategies for sustainable perovskite solar panels

by Clarence Oxford

Los Angeles CA (SPX) Jul 24, 2024

Researchers at the National Renewable Energy Laboratory (NREL) are examining the future of perovskite solar panels, focusing on scaling, deploying, and designing panels to be recyclable.

Perovskite solar panels could play a key role in global efforts to reduce greenhouse gas emissions. With the technology still in its developmental stages, researchers are emphasizing the importance of designing these panels to minimize environmental impact.

“When you have a technology in its very early stages, you have the ability to design it better. It’s a cleaner slate,” said Joey Luther, a senior research fellow at the U.S. Department of Energy’s (DOE’s) National Renewable Energy Laboratory (NREL) and coauthor of the newly published article in the journal Nature Materials. “Pushing perovskite PV toward enhanced sustainability makes more sense at this stage. We’re thinking about how we can make sure we have a sustainable product now rather than dealing with sustainability issues toward the end of its practical life.”

The article highlights the PV research community’s influential position to prioritize remanufacturing, recycling, and reliability efforts, aiming to make perovskite PV one of the most sustainable energy sources available.

“Perovskites could unlock the next evolution of high-efficiency PV, and it is our responsibility to assure they are manufactured, used, and recycled sustainably,” said the lead author of the study, Kevin Prince, a former graduate researcher at NREL who now researches perovskites at Helmholtz Zentrum Berlin in Germany.

While silicon solar panels dominate the industry and cadmium telluride (CdTe) panels have established recycling programs, perovskites are at a critical point where sustainability issues can be addressed from the start.

The most effective circular economy begins at the design stage, considering materials sourcing, product lifetime, and end-of-life management. Researchers suggest assessing environmental impacts by looking at carbon emissions during production, embodied energy, sustainable material sourcing, and module circularity.

The journal article identifies critical sustainability concerns for each component of a perovskite solar panel. For instance, lead can be diluted with metals like tin to reduce lead content, though this may affect PV efficiency and durability. Expensive precious metals such as silver and gold could be replaced with cheaper alternatives like aluminum, copper, or nickel. Fluorine-tin oxide is recommended over the scarcer indium-tin oxide for front electrodes.

“We want to have the lowest amount of embodied energy in the fabrication,” Luther said. “We want to have the lowest amount of emissions in the fabrication. At this stage, now is the chance to look at those components. I don’t think we have to change anything. It’s more a matter of what decisions should be made, and these arguments should certainly be discussed.”

The authors discuss various ways to improve the circularity of perovskite panels. Remanufacturing involves reusing parts from old modules to make new ones, while recycling converts waste materials into raw materials for reuse. Attention is needed for the specialized glass used in perovskite modules, which is crucial for structural support and protection while allowing maximum sunlight penetration. Establishing a recycling pathway for this glass will be essential as PV deployment increases.

Silvana Ovaitt, a PV researcher and coauthor of the paper, noted that cleaner electricity grids will lead to cleaner manufacturing processes, further reducing emissions.

“Another concern is the transportation of the final modules and the raw glass because those are the heaviest items,” Ovaitt said. “Local manufacturing will be a great way to reduce those carbon impacts.”

The researchers explain that increasing the durability of PV modules, thereby extending their useful life, is a more effective approach to reducing net energy, energy payback, and carbon emissions than designing for circularity alone. A longer lifespan means panels won’t need to be recycled as often.

“Ultimately, we want to make them as durable as possible,” Luther said. “But we also want to consider the aspects of whenever that time does come. We want to be deliberate about how to take them apart and to reuse the critical components.”

Research Report:Sustainability pathways for perovskite photovoltaics